Jet Tools JWBS-14OCS Bedienungsanleitung

Operating Instructions and Parts Manual 14-inch Woodworking Band Saw Models: JWBS-14OS, JWBS-14CS WALTER MEIER (Manufacturing) Inc. 427 New S

107. Place motor over rubber grommets and fasten to stand top with four hex cap screws, eight flat washers, four lock washers, and four hex nuts, as

119. Place v-belt over both pulleys. See Figure 8. 10. Tension v-belt by moving motor away from the saw body and tighten the motor mount nuts. (Do n

12Assembly of JWBS-14CS Tools Required for Assembly Metric combination wrench set and adjustable wrench #1 and #2 cross point screwdrivers Exposed

13IMPORTANT: When moving the pulleys, do not position them beyond the end of the shaft. Both pulleys must fully engage the shaft and the key. 7. Op

1413. To mount the table, remove pin and insert from the table (Figure 19). 14. Orient the table so the saw blade will pass through the slot in th

15Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether t

16Extension Cords Use only three wire extension cords that have three-prong grounding plugs and three-pole receptacles that accept the tool’s plug. M

175. Loosen jam nut and turn table stop (Figure 26) left or right to raise or lower the stop. Tighten jam nut to hold table stop in place. 6. Unl

183. As you become more experienced with the saw, you may find it necessary to change the blade tension from the initial setting. Changes in blade w

193. Tighten lock knob. Make sure blade guide blocks (C, Figure 30) are still flat to the blade. If adjustment is necessary, loosen lock knob (A, F

2 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Au

208. Notice the bearing holder on the shaft is eccentric. Index the bearing shaft to another position and slide it back in, making sure the flange o

21Troubleshooting JWBS-14CS/OS Band Saw Trouble Probable Cause Remedy Saw stops or will not start. Saw unplugged. Check all plug connections. Fuse

22Optional Accessories 708718R JRF-14 Deluxe Rip Fence Assembly with Resaw Includes guide bars, rip fence assembly, resaw post, fasteners, and mo

23Body Assembly (JWBS-14CS/OS Band Saw) Index No. Part No. Description Size Qty 1 ... 150100AW ...Upper Arm Frame ...

24Body Assembly (JWBS-14CS/OS Band Saw) Index No. Part No. Description Size Qty 59 ... 995001...Power Cord (Switch To

25Body Assembly (JWBS-14CS/OS Band Saw)

26Closed Stand Assembly (JWBS-14CS Band Saw) Index No. Part No. Description Size Qty 1 ... 150501W ...Stand ...

27Closed Stand Assembly (JWBS14-CS Band Saw)

28Open Stand Assembly (JWBS-14OS Band Saw) Index No. Part No. Description Size Qty 1 ... 150602W ...Top Plate ...

29Open Stand Assembly (JWBS-14OS Band Saw)

3 Table of Contents Warranty and Service...

30Electrical Connections – 115 volt (JWBS-14CS/OS Band Saw)

31Electrical Connections – 230 volt (JWBS-14CS/OS Band Saw)

32 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.walter

4 Warni ng 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on

5 21. Make your workshop child proof with padlocks, master switches or by removing starter keys. 22. Give your work undivided attention. Looking ar

6 Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for a Model JWBS-

7 Unpacking – JWBS-14OS Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent.

8 Unpacking – JWBS-14CS Open both shipping containers and check for shipping damage. Report any damage immediately to your distributor and shipping a

9 Assembly of JWBS-14OS NOTE: If any of the assembly procedures need further clarification, refer to the exploded views in the back of this manual.